Removal

1.	Disconnect the parking brake switch connector(A).

2.	Remove the mounting clip(B), then remove the parking brake cable(C).

3.	Remove the parking brake pedal mounting bolts and nut(D), then remove the parking brake pedal.

4.	Remove the floor console. (Refer to BD Gr. 'Console').

5.	Remove the floor carpet.

6.	Remove the parking brake cable(A).

1.	Raise the vehicle, and make sure it is securely supported.

2.	Remove the rear tire and wheel, then remove the brake caliper. (Refer to "Rear disc brake removal")

3.	Remove the parking brake cable (B), after remove the clip (A).

4.	Remove the shoe hold down pin (A) and spring (B) by pressing and rotating the spring.

5.	Remove the adjuster assembly (B) and the lower return spring (A).

6.	Remove the upper return spring (C) and the brake shoes (D).

7.	Remove the operating lever assembly (E).

Installation

1.	Install the operating lever assembly (E).

2.	Install the upper return spring (C) and the brake shoes (D).

3.	Install the adjuster assembly (B) and the lower return spring (A).

4.	Install the shoe hold down pin (A) and spring (B) by pressing and rotating the spring.

5.	Install the parking brake cable (B), then install the clip (A).

6.	Install the rear brake disc, then adjust the rear brake shoe clearance. (1) Remove the plug from the disc. (2) Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 5 notches in the opposite direction.

7.	Install the brake caliper. (Refer to "Rear brake installation")

8.	Install the tire and wheel.

9.

If the parking brake shoe or the brake disc are replaced a newly one, perform the brake shoe bed-in procedure. (1) While operating the parking brake pedal for 69 N(7 kgf, 15 lb) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 60 kph (37.3 mph). (2) Repeat the above procedure more than two times. (3) Must be held on at 30% uphill. After adjusting parking brake, notice following matter; 1. Must be free from troubles when the parking pedal is operated at 981N(100 kgf, 220 lb). 2. Check that all parts move smoothly. 3. The parking brake indicator lamp must be on after the parking pedal is worked and must be off after the pedal is released.

1.	Install the parking brake cable(A).

2.	Install the floor carpet.

3.	Install the floor console. (Refer to BD Gr. 'Console').

4.	Install the parking brake pedal , and then install the parking brake pedal mounting bolts and nut(D).

5.	Install the parking brake cable(C) , and then install the mounting clip(B).

6.

Adjust the parking brake pedal stroke by turning the adjusting nut(A). (1) Adjust the adjusting nut(A) so that parking brake pedal stroke is to be 88~98mm (3.46~3.86in) when operating effort is 196 N(20 kgf, 44 lb) after full stroke operation of parking brake pedal over 3 times for setting parking wire. 1. The parking brake adjustment must be carried out after adjusting the rear shoe. 2. After adjusting parking brake, notice following matter. 1) Must be free from clearance between adjusting nut and pin. 2) Check securely that the brake is not dragging.

7.	Reconnect the parking brake switch connector(A).

Adjustment

1.	Raise the vehicle, and make sure it is securely supported.

2.	Remove the rear tire and wheel.

3.	Remove the plug from the disc.

4.	Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 5 notches in the opposite direction.

1.

Adjust the adjusting nut(A) so that parking brake pedal stroke is to be 88~98mm (3.46~3.86in) when operating effort is 196 N(20 kgf, 44 lb) after full stroke operation of parking brake pedal over 3 times for setting parking wire. 1. The parking brake adjustment must be carried out after adjusting the rear shoe. 2. After adjusting parking brake, notice following matter. 1) Must be free from clearance between adjusting nut and pin. 2) Check securely that the brake is not dragging.