| 1. |
Remove the rear wheel &
tire. |
| 2. |
Remove the wheel speed sensor connector (A)
and the parking brake cable (B) from the rear axle
carrier.
|
| 3. |
Remove the caliper assembly (B) by loosening
the mounting bolts (A) and then suspend it with wire.
|
| 4. |
Support the lower portion of the rear lower
arm the jack. |
| 5. |
Disconnect the shock absorber with body by
loosening the bolt (A).
|
| 6. |
Remove the center and main
muffler.
(Refer to EM
group) |
| 7. |
Remove the propeller shaft assembly
(A).
(Refer to DS group)
|
| 8. |
Support the rear cross member assembly with
a jack.
|
| 9. |
Remove the rear cross member stay (A) by
loosening the mounting bolt (B) and nut (C).
|
| 10. |
Remove the cross member from the body by
loosening the mounting bolts (A) and nuts (B).
|
| 11. |
Remove the split pin (A) and castle nut (B)
from the upper arm ball joint (C).
|
| 12. |
Disconnect the upper arm ball joint (A) with
the rear carrier assembly using a SST (09568-34000).
|
| 13. |
Remove the rear upper arm (B) by loosening
the bolts and nut (A).
|
| 1. |
Check the bushing for wear and
deterioration. |
| 2. |
Check the rear upper arm or damage and
deformation. |
| 3. |
Check for all bolts and
nut. |
| 1. |
Connect the rear upper arm with the cross
member (B) and then tighten the bolts and nuts (A).
Tightening
torque :
100 ~ 120N.m (10.0 ~ 12.0kgf.m, 72 ~
87lb-ft)
|
|
| 2. |
Connect the rear upper arm ball joint (C)
with the carrier assembly and then install the castle nut (B) and
the split pin (A).
Tightening
torque :
80 ~ 100N.m (8.0 ~ 10.0kgf.m, 58 ~
72lb-ft)
|
|
| 3. |
Install the rear cross member to the body by
tightening the mounting bolts (A) and nuts (B).
Tightening
torque :
160 ~ 180N.m (16.0 ~ 18.0kgf.m, 116 ~
130lb-ft)
|
|
| 4. |
Install the rear cross member stay (A) by
tightening the mounting bolt (B) and nut (C).
Tightening
torque :
70 ~ 90N.m (7.0 ~ 9.0kgf.m, 51 ~
65lb-ft)
|
|
| 5. |
Install the propeller shaft (A). (Refer to
DS group)
|
| 6. |
Install the center and main
muffler.
(Refer to EM
group) |
| 7. |
Connect the rear shock absorber to the body
and then tighten the bolt (A).
Tightening
torque :
140 ~ 160N.m (14.0 ~ 16.0kgf.m, 101 ~
116lb-ft)
|
|
| 8. |
Install the rear caliper assembly (B) to the
carrier assembly and then tighten the mounting bolts
(A).
Tightening
torque :
50 ~ 60N.m (5.0 ~ 6.0kgf.m, 36 ~
43lb-ft)
|
|
| 9. |
Install the wheel speed sensor (A) and
parking brake cable (B) to the carrier assembly.
|
| 10. |
Install rear wheel & tire.
Tightening
torque :
90 ~ 110N.m (9.0 ~ 11.0kgf.m, 65 ~
80lb-ft)
| | |
