| 1. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is
securely supported. |
| 2. |
Remove the rear wheel and tire (A) from the
rear hub (B).
|
Be careful not to damage to the hub
bolts (C) when removing the rear wheel and tire
(A). | |
| 3. |
Remove the split pin (A), then remove castle
nut (B) and washer (C) from the front hub under applying the
brake.
|
| 4. |
Remove the mounting bolt (B) of the rear lower
arm(A) and the rear carrier, while supporting the lower arm (A) with
a jack as shown in the illustration. Loosen the mounting bolt (C) of
the cross member and the rear lower arm.
|
| 5. |
Remove the spring (A), the upper pad (B) and
the lower pad (C).
|
| 6. |
Remove the rear shock absorber
(A).
|
| 7. |
Remove the assist arm (A) and the trailing arm
(B) from the rear axle carrier.
|
Remove the rear assist arm ball joint by
using the special
tool(09568-4A000). |
|
| 8. |
Remove the rear stabilizer link (A) from the
rear axle carrier.
|
| 9. |
Remove the brake caliper mounting bolts (A),
and then place the brake caliper assembly (B) with wire as shown in
the illustration.
|
| 10. |
Remove the wheel speed sensor connector (A)
and the parking brake cable (B) from the rear axle
carrier.
|
| 11. |
Remove the split pin (A) and the castle nut
(B) from the rear upper arm ball joint (C), and then remove the rear
upper arm ball joint (C) by using the special
tool(09568-34000).
|
| 12. |
Remove the rear axle carrier
assembly. |
| 1. |
Install the rear axle carrier
assembly. |
| 2. |
Install the split pin (A) and the castle nut
(B) to the rear upper arm ball joint (C).
Tightening
torque Nm (kgf-m, lb-ft) :
78.5~98.1 (8.0~10.0,
57.9~72.3)
|
|
| 3. |
Install the wheel speed sensor connector (A)
and the parking brake cable (B) to the rear axle
carrier.
|
| 4. |
Install the brake caliper (B), then tighten
the brake caliper mounting bolts (A).
Tightening
torque Nm (kgf-m, lb-ft) :
63.7~73.5 (6.5~7.5,
47.0~54.2)
|
|
| 5. |
Install the rear stabilizer link (A) from the
rear axle carrier.
Tightening
torque Nm (kgf-m, lb-ft) :
Nut(B) : 58.8~78.5 (6.0~8.0,
43.4~57.9)
|
|
| 6. |
Install the assist arm (A) and the trailing
arm (B) to the rear axle carrier.
Tightening
torque Nm (kgf-m, lb-ft) :
Bolt (C) : 137.3~156.9 (14~16,
101.3~115.7)
Nut (D) : 98.1~117.7 (10~12,
72.3~86.8)
Nut (E) : 137.3~156.9 (14~16,
101.3~115.7)
Bolt (F) : 137.3~156.9 (14~16,
101.3~115.7)
|
|
After checking the
distance(467±10mm(18.39±0.39in)) between the wheel housing
garnish(A) and the hub assembly(B) as shown in the
illustration, tighten the mounting bolts and nuts of rear
chassis part with specified
torque. |
|
| 7. |
Install the rear shock absorber
(A).
Tightening
torque Nm (kgf-m, lb-ft) :
Bolt (B) : 137.3~156.9 (14~16,
101.3~115.7)
Nut (C) : 98.1~117.7 (10.0~12.0,
72.3~86.8)
|
|
| 8. |
Install the spring (A), the upper pad (B) and
the lower pad (C).
|
| 9. |
Install the mounting bolt (B) of the rear
lower arm(A) and the rear carrier with a specified torque, while
supporting the lower arm (A) with a jack as shown in the
illustration. Tighten the mounting bolt (C) of the cross member and
the rear lower arm with a specified torque.
Tightening
torque Nm (kgf-m, lb-ft) :
Bolt (B) : 137.3~156.9 (14~16,
101.3~115.7)
Nut (C) : 137.3~156.9 (14~16,
101.3~115.7)
|
|
| 10. |
Install the washer (C), castle nut (B) and
split pin (A) to the rear hub assembly.
Tightening
torque Nm (kgf-m, lb-ft) :
196.1~274.6 (20~28,
144.7~202.5)
|
|
The washer (C) should be assembled with
convex surface outward when installing the castle nut (B) and
split pin (A). |
|
| 11. |
Install the wheel and tire (A) to the rear hub
(B).
Tightening
torque Nm (kgf-m, lb-ft) :
88.3~107.9 (9~11,
65.1~79.6)
|
|
Be careful not to damage the hub bolts
(C) when installing the rear wheel and tire
(A). | |
| 12. |
Check the alignment. (Refer to SSgroup
'Tires/Wheels - alingment') |
| 1. |
Remove the brake disc from the rear axle
carrier assembly. |
| 2. |
Remove the hub assembly mounting bolts (B)
from the rear axle carrier (A).
|
| 3. |
Remove the hub assembly (B) and the parking
brake assembly (C) from the rear axle carrier (A).
|
Do not disassemble the hub
assembly. | |
| 1. |
Check the hub for cracks and the splines for
wear. |
| 2. |
Check the brake disc for scoring and
damage. |
| 3. |
Check the rear axle carrier for
cracks |
| 4. |
Check the bearing for cracks or
damage. |
| 1. |
Install the parking brake assembly (C) and the
hub assembly (B) to the rear axle carrier (A).
|
| 2. |
Install the hub assembly to the rear axle
carrier (A) and then tighten the mounting bolt (B).
Tightening
torque Nm (kgf-m, lb-ft) :
78.5~88.3 (8~9,
57.9~65.1)
|
|
| 3. |
Install the brake disc to the rear axle
carrier assembly.
Tightening
torque Nm (kgf-m, lb-ft) :
Screw: 4.9~5.9 (0.5~0.6,
3.6~4.3)
| | |
