| 1. |
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is
securely supported. |
| 2. |
Remove the front wheel and tire (A) from the
front hub (B).
|
Be careful not to damage to the hub
bolts (C) when removing the front wheel and tire
(A). | |
| 3. |
Remove the split pin (A), then remove castle
nut (B) and washer (C) from the front hub under applying the
brake.
|
| 4. |
Remove the brake caliper mounting bolts (A),
and then place the brake caliper assembly (B) with
wire.
|
| 5. |
Remove the tie rod end ball joint from the
knuckle.
| (1) |
Remove the split pin
(A). |
| (2) |
Remove the castle nut
(B). |
| (3) |
Disconnect the ball joint (C) from
knuckle (D) using the special tool (09568-4A000).
|
Apply a few drops of oil to the
special tool. (Boot contact
part) | | |
| 6. |
Remove the wheel speed sensor (B), the strut
lower mounting bolt (C) and the lower arm mounting bolt (D) from the
knuckle (A).
|
| 7. |
Remove the hub and knuckle
assembly.
|
Be careful not to damage the boot and
rotor
teeth. | |
| 1. |
Install the hub and knuckle
assembly. |
| 2. |
Install the wheel speed sensor (B), the
strut lower mounting bolt (C) and the lower arm mounting bolt (D)
from the knuckle (A).
Tightening
torque Nm (kgf-m, lb-ft) :
Wheel speed sensor (B):
6.9~10.8 (0.7~1.1,
5.1~8.0)
Bolts (C): 152.0~171.6 (15.5~17.5,
112.1~126.6)
Bolt (D) : 98.1~117.7 (10~12,
72.3~86.8)
|
|
| 3. |
Install the tie rod end ball joint (C) to
the knuckle (D). |
| 4. |
Install the castle nut (B) and the split pin
(A).
Tightening
torque Nm (kgf-m, lb-ft) :
23.5~33.3 (2.4~3.4,
17.4~24.6)
|
|
| 5. |
Install the brake caliper (B) and then
tighten the mounting bolts (A).
Tightening
torque Nm (kgf-m, lb-ft) :
73.5~83.4 (7.5~8.5,
54.2~61.5)
|
|
| 6. |
Install the washer (C), castle nut (B) and
split pin (A) to the front hub assembly.
Tightening
torque Nm (kgf-m, lb-ft) :
196.1~274.6 (20~28,
144.7~202.5)
|
|
The washer (C) should be assembled
with convex surface outward when installing the castle nut (B)
and split pin (A). |
|
| 7. |
Install the wheel and tire (A) to the front
hub (B).
Tightening
torque Nm (kgf-m, lb-ft) :
88.3~107.9 (9~11,
65.1~79.6)
|
|
Be careful not to damage the hub bolts
(C) when installing the front wheel and tire
(A). | |
| 1. |
Remove the brake disc (B) from the knuckle
assembly (A).
|
| 2. |
Remove the hub assembly mounting bolts (B)
from the knuckle (A).
|
| 3. |
Remove the hub assembly (C) and the dust
cover (B) from the knuckle (A).
|
Do not disassemble the hub
assembly. | |
| 1. |
Check the hub for cracks and the splines for
wear. |
| 2. |
Check the brake disc for scoring and
damage. |
| 3. |
Check the knuckle for
cracks. |
| 4. |
Check the bearing for cracks or
damage. |
| 1. |
Install the dust cover (B) to the knuckle
(A) and then tighten the mounting bolt (C).
Tightening
torque Nm (kgf-m, lb-ft) :
6.9~10.8 (0.7~1.1,
5.1~8.0)
|
|
| 2. |
Install the hub assembly to the knuckle (A)
and then tighten the mounting bolt (B).
Tightening
torque Nm (kgf-m, lb-ft) :
78.5~98.1 (8~10,
57.9~72.3)
|
|
| 3. |
Install the brake disc (B) to the knuckle
assembly (A).
Tightening
torque Nm (kgf-m, lb-ft) :
Screw(C): 4.9~5.9 (0.5~0.6,
3.6~4.3)
|
| |
