The POWER WINDOW ASSIST
SWITCH ASSY shall be one component of the CAN SYSTEM. The SWITCH ASSY
POWER WINDOW ASSIT shall communicate through CAN with the BCM, the SEAT
ECU, the TILT ECU, the SWITCH ASSY POWER WINDOW MAIN.
| 1. |
POWER WINDOW OPERATIOPN BY BUTTON
The SIDE P/WMW BUTTON shall output signal to
the 2 operations of the Manual
UP/DOWN |
| 2. |
PASSIVE OPERATION OF MIRROR’S POSITION BY
MANUAL SW (UP, DOWN, LEFT, RIGHT)
THE RECEIPT FROM P/WDW MAIN SW WITH CAN
COMMUNICATION |
| 3. |
THE MEMORY AND REMINDING OPERATION FOR
POSITIONING THE MIRROR USING MEMORY SWITCH(FOR 2
PASSENGERS)
THE RECEIPT FROM P/WDW MAIN SW WITH CAN
COMMUNICATION |
| 4. |
RECEIPT BY CENTRAL DOOR LOCK/UNLOCK BUTTON
OPERATION WITH CAN COMMUNICATION |
| 5. |
CONTAINMENT AND RETURN FUNCTION OF OUTSIDE
MIRROR |
| 1. |
POWER WINDOW CONTROL
| (1) |
POWER WINDOW Operating
condition
| A. |
POWER WINDOW LOCK SW(FROM DDM) OFF
& POWER WINDOW TIMER(FROM BCM) ON or IGN2(ADM)
ON | |
| (2) |
POWER WINDOW UP/DOWN
operating
| A. |
Receiving P/WDW UP/DOWN (FROM DDM
or ADM itself) signal input under POWER WINDOW drive
condition, Run assist's POWER WINDOW. Can not be
outputed more than 15 seconds by same one-way
only. | | |
| 2. |
OUTSIDE MIRROR CONTROL BY MANUAL
SWITCH
| (1) |
ASSIST SIDE OUTSIDE MIRROR
OPERATION
| A. |
The ACC ON state, if the mirror
select switch in DDM is the RH state and the mirror
direction switches (UP, DOWN, LEFT, and RIGHT) are
operated, then the mirror motor shall be drive to
control the mirror to the desired direction by receiving
CAN msg. At this time, Up/Down direction conversion or
Right/Left direction conversion, it have 100 ms Delay
Times. |
| |
| 3. |
OUTSIDE MIRROR MEMORY OPERATION BY MEMORY
SWITCH
| (1) |
AFTER RECEPTION FROM THE P/WDW MAIN SW
WITH CAN COMMUNICATION, MEMORIZE ASSIST SIDE O/S MIRROR
POSITION.
Except, when the mirror manual switch at
the RH is operated, the mirror position at RH shall not be
memorized. |
| (2) |
WHEN GETTING RID OF BATTERY, SAVE THE
MIRROR POSITION MEMORIZED BY MEMORY SWITCH TO
EEPROM. | |
| 4. |
OUTSIDE MIRROR REMINDING OPERATION BY MEMORY
SWITCH
| (1) |
Drive MIRROR reminding to position that
is remembered if receive MIRROR reminding request (CAN) from
DDM in IGN2 ON state. |
| (2) |
Reminding operation of position that is
not remembered is not
operation. |
| (3) |
It act reminding to position that is
required lastly if it receive reminding request (FROM DDM) of
different position during reminding
operation. |
| (4) |
Reminding prohibition
condition
| A. |
INHIBIT "P" SW(FROM IMS) is
OFF |
| C. |
RH side MIRROR MANUAL SW's
manufacturing (FROM DDM) is
occured |
| D. |
vehicle speed is more than 3 Km/h
(FROM
BCM) | | |
| 5. |
OUTSIDE MIRROR FAIL SAFE FUNCTION
| (1) |
If the sensor variation of 80㎷ and more
is not occurred even there is an input variation from the
position sensor when motor is driven, it shall be considered
as occurring defects such as the harness disconnection, the
motor failure, or the sensor malfunction so that the auto
control operation should be
quitted. |
| (2) |
The mirror driving signal should not
output over 15 seconds continuously. (Both the memory
reminding and the manual switching
operation) |
| (3) |
Monitoring the Reminding Operation Time.
If the reminding operation does not complete within 40 seconds
after starting, the output of the mirror motor should be
quitted and the reminding operation should be
finished. | |
